Torque Information

Torque Information

Pro-Bolt offer a variety of products in three different materials, each offering a different level of strength suitable for different applications. Pro-Bolt Limited strongly recommends that you seek the advice of a professional when fitting any bolts. You are entirely responsible for ensuring any bolts are correctly fitted and ProBolt Fasteners Limited shall not be liable for any damage or harm that is as a result of you having fitted the bolt without having sought such advice or for any incorrectly fitted bolt.

When fitting any Pro-Bolt bolt kit or accessory, it is essential to check your Pro-Bolt part with your manufacturer’s original. We Supply a Pro-Bolt Thread Gauge to assist with this. When comparing bolts, you must check the thread diameter, length of bolt and thread pitch, and when comparing other items, check that dimensions are the same for all contact parts.

Our accessories are matched to specific bike models by premeasuring those bikes – however, it is possible that manufacturers apply changes mid model without our knowledge, and we therefore require that you exercise due care prior to fitting. If you are not confident about fitting our products yourself, we recommend that you take our products to a professional.

When fitting a bolt kit replace one bolt at a time - with an identical length bolt (lubricated where required) follow our torque guides for the relevant material. Bolt kits in contact with the screen or fairing contain plastic washers which should be used under the head of all bolts to prevent scratching paintwork/plastic. In our fairing kits you will also find a number of collars, where your original bolts have shoulders, these are used to replicate the collar allowing the bolt to locate into the fairing effectively.

Please adhere to the following guide at all times:

Aluminium

Do not use aluminium bolts in any stress areas e.g. Brake Caliper Fixings, Suspension Mounts, Footrest Hangers, Grab Rails etc.

Aluminium bolts can be used on: Engine Casings, Fairings, Screens, Fuel Caps, Number Plates, Heel Guards, Chain Guards etc. Always apply a suitable lubricant on threads. Do not over-tighten – aluminium is a soft material so to prevent damage, observe the following torque guide.

Sprocket Nut Safety: Aluminium Sprocket Nuts are manufactured to allow a torque of 33 ft/lbs or 44Nm. When fitting, wrap with a thin, tough tape such as Teflon to prevent scratching. We recommend applying a medium strength Threadlock.

Oil Filler Caps Safety: Oil Filler caps are supplied with an ‘O’ ring, which must be used to achieve an airtight seal. Test to ensure oil is not leaking. If the seal is not airtight, DO NOT USE, as oil leaking onto areas such as the rear tyre may be dangerous.

Reservoir Cap Safety: Reservoir fluid is corrosive; care must be taken to ensure fluid is not spilt on hands or any areas of the bike. If spilt wash affected area with plenty of soapy water immediately. Reservoir caps must be fitted with the use of the original membrane. Identical length replacement bolts are provided where necessary – these should be hand tightened to achieve an airtight seal, which should be checked after a short test ride to ensure fluid does not leak.
DO NOT USE if any leakage has occurred as this may affect the performance of the brake/clutch. Contact Pro-Bolt directly if any problems are encountered.

Yoke Nuts: Ascertain manufacturer’s torque guide, then reduce values by 30%.

Maximum Torque Guide - Aluminium in Nm
Thread Diameter	3mm	4mm	5mm	6mm	8mm	10mm
Flanged Hex Head Bolt	n/a	n/a	6.00	8.00	12.00	20.00
Socket Cap Bolt	1.50	3.50	6.00	6.00	10.00	n/a
Dome Head / Fairing Bolt	n/a	2.50	4.00	5.00	8.50	16.00
Countersunk Bolt	n/a	2.00	2.50	5.00	8.00	n/a

Stainless Steel

Torque Settings

Guide for Motorcycle Applications

For stress areas and safety critical components, Pro-Bolt recommends OEM torque values be used for both Stainless Steel and Titanium fasteners.

Guide for Fasteners in General Usage

For fasteners in other applications please refer to the table opposite.

Please note torque values are provide in Newton Metres for lubricated threads.

Pro-Bolt also provides fitment instructions with all orders.

Please be aware that not all stainless steel is suitable for stress areas.
However, Pro-Bolt 316 stainless steel is suitable for Engine Casings, Fairings, Screens, Front Axle Pinch, Caliper Pinch Bolts, Caliper Mount Bolts, Footrest Hanger Bolts, Clip-On Handle Bar Bolts, Brake/Clutch Pinch Perch, Top/Bottom Yoke Clamp Bolts, Sprocket Nuts, Disc Bolts etc.

Cam Cover Bolt Fitment

Top Cam Cover Bolts: Remove and fit one bolt at a time. To avoid a potential snapping of the thread, ensure an even purchase when fitting. Use manufacturer’s original seals in conjunction with seal supplied by Pro-Bolt. Torque to manufacturers recommended guide.

Side Cam Cover Bolts: Remove and fit one bolt at a time. Replace crush washers with new un-used crush washers and torque to manufacturers recommended guide.

Maximum Torque Guide - Stainless Steel in Nm
Thread Diameter	3mm	4mm	5mm	6mm	8mm	10mm	12mm	14mm
Flanged Hex Head Bolt	2.00	5.00	12.00	15.00	35.00	38.00	97.50	155.20
Socket Cap Bolt	1.73	4.00	10.00	14.00	25.00	38.00	n/a	n/a
Dome Head / Fairing Bolt	n/a	3.50	5.00	11.00	16.00	26.00	n/a	n/a
Countersunk Bolt	n/a	3.50	5.00	8.00	15.00	20.00	n/a	n/a

Titanium

Before you start work on your machine ensure the bike is secure, positioned on a paddock stand where necessary. Where our products are used in safety critical areas it is essential to use the correct torque and fit with care.

When fitting we recommend:

- When fitting it is essential to match the Pro-Bolt with the bolt you are replacing. The thread, pitch and length should be identical. Should any differences occur, please contact Pro-Bolt prior to fitting. This is particularly important in areas such as Disc Bolts and Brake Caliper Bolts.

- We recommend the use of a T-Bar or torque wrench to achieve an even purchase.

- Select appropriate antiseize lubricant or thread lock.

- Torque for Flanged Hex Head and Tapered Socket Cap Bolts - use torque values specified by your equipment manufacturer.

- Torque for Dome Head and Countersunk Bolts - use the following torque guide.

- After fitting new parts we recommend you take your motorcycle for a short test ride, riding with care. Examine parts after the test ride to ensure all parts are secure. Should you have any queries, please contact Pro-Bolt directly before riding your bike.

Disc Rotor Bolts: We recommend the use of a medium strength Threadlock be used with both Titanium & Stainless Steel Disc Rotor Bolts. We replicate the dimensions of manufacturer’s original parts and this often results in bolts with a low head profile, therefore a small and shallow drive. We recommend the use of a T-Bar or torque wrench to achieve an even purchase. We recommend you use torque values specified below:

- For bolts with a 6mm Thread Diameter: 20Nm
- For bolts with a 8mm Thread Diameter: 22Nm
- For bolts with a 10mm Thread Diameter: 25Nm